Getting Familiar with Plumbing: The First Step for Bathtub Installation

Click Here

We have found this article about Installing A Bathtub listed below on the internet and decided it made sense to share it with you on this site.


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't exactly rocket science, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Changing an old tub with a new one is also a moderately tough task. If the old tub is easily easily accessible, the task can move rapidly; if you have to open up a wall surface to eliminate the old bathtub and position the brand-new bathtub, the job is a lot harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to leave the old bathtub and embeded in the new one. Make sure you have qualified yourself for the job and fit trying it. As opposed to employing a professional to take over a halfway-completed task, it is far better to consider using one before you start. Possibilities are you might require a specialist plumber to make tube links.
This post will help you install a new bath tub in your shower room if you have actually currently acquired a brand-new tub as well as don't need to change the arrangement of your previous water pipes.
Your tools and material list need to make up the following:
  • New Bathtub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Getting ready for the Installment


    First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to prevent stress on the tub.
    Fit the versatile faucet ports to the bottom of both faucets using 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you use every one of the supplied washers.
    Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be suited its final setting.

    Removing Old Taps


    If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water. After doing so, switch on the taps to drain pipes any water staying in the system. The process of removing the existing taps can be rather problematic due to the restricted gain access to that is commonly the instance.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel all set for the staying water that will certainly come from the pipelines. Once the supply pipes have been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
    Before carrying on to fit the brand-new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.

    Mounting the Bath tub


    Making use of both wood boards under its feet, place the bath tub in the required position. The wooden boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto four small points.
    The next objective is to make certain that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bath tub till the level reviews degree.
    To mount faucets, fit all-time low of the outermost versatile tap adapter to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
    Activate the water system and also examine all joints and also brand-new pipework for leakages and also tighten them if necessary. Fill up the bath tub and likewise inspect the overflow electrical outlet and also the regular outlet for leakages.
    Ultimately, deal with the bath paneling as explained in the producer's user's manual. Tiling and also sealing around the bath tub ought to wait till the tub has been utilized at the very least once as this will settle it right into its last placement.

    Suitable New Touches


    If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a link to the existing supply pipes.
    If you require to fit a monobloc, then you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
    Next off, position the faucet in the mounting hole in the bath/basin making sure that the washing machines are in location in between the faucet as well as the sink. Protect the faucet in position with the maker given backnut. When the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type ought to be linked to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.

    Tiling Around the Tub


    In the location where the bath meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to crack an inflexible seal, causing the water to permeate the wall in between the bathroom as well as the tiling, bring about issues with wetness and possible leaks to the ceiling below.
    You can select from a range of coloured sealants to blend in your components and installations. They are sold in tubes and also cartridges, as well as can sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can split fairly early if you do not take into consideration this movement before sealing.
    Conversely, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water resistant sticky and also cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    I hope you enjoyed our part about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for finding the time to browse our short article. Do you know about another person who is fascinated about the subject? Feel free to share it. We value reading our article about Installing A Bathtub.


    Check Us Out

    Leave a Reply

    Your email address will not be published. Required fields are marked *